This new OE German quality carburetor has the later style accelerator pump linkage already installed, and will work perfectly with generator or alternator without any modifications.

The Brosal 34 PICT-3 carburetor which is sold by all other VW parts suppliers was built for use with a standard generator, and when used with an alternator (fatter diameter), the accelerator pump linkage will hit the body of the alternator. The easiest way to fix this problem is to grind a little bit of the alternator body away where the linkage bolt head is hitting. You can also use 2 or 3 gaskets between the carb. and manifold which will raise up the carb. slightly and therefore require less grinding to the alternator body. If you would like this carburetor, see part number VWC-113-129-031-K.

Special note about carburetors: they are non returnable! We sell only 100% brand-new carburetors manufactured by Weber,Solex, Brosal and Bruck. Every carburetor we sell has been pre-tested by each manufacturer and given 100% perfect condition stamp of approval. When considering the purchase of a new carburetor- please be advised that we cannot return any carburetor for any reason. Before installing a new carburetor- please insure that the fuel lines and gas tank have been thoroughly cleaning and flushed of all dirt and rust. Also - always replace all rubber fuel hoses and filters. It is your responsibility to guarantee the cleanliness of your fuel system.

How long should your 25 year old plus carburetor last? Every time you push the throttle, the throttle shaft wears against the carburetor body. After years of this, the wear between the shaft and body allows air to slip through the gap entering the engine. This old carburetor has no way to adjust for this un-metered air, throwing the idle fuel mixture so far out of adjustment that you will never be able to get the car to idle properly once it has warmed up. The only answer? You need to buy a 100% new carb.For the best results we recommend that you use a Vacuum advance distributor-see part #VWC-043-905-205

Special note about carburetors: they are non returnable! We sell only 100% brand-new carburetors manufactured by Weber,Solex, Brosal and Bruck. Every carburetor we sell has been pre-tested by each manufacturer and given 100% perfect condition stamp of approval. When considering the purchase of a new carburetor- please be advised that we cannot return any carburetor for any reason. Before installing a new carburetor- please insure that the fuel lines and gas tank have been thoroughly cleaning and flushed of all dirt and rust. Also - always replace all rubber fuel hoses and filters. It is your responsibility to guarantee the cleanliness of your fuel system.

New 34 Pict-3 Brosal Mexican Carburetor

. These are Genuine VW end casting for the Left side that connect the Center intake manifold section # VWC-113-129-701M to the cylinder head. This intake manifold fits all 1600cc dual port Type 1 style engines. The carborator that fits this manifold is the 34 PICT-3, part #C24-113-129-031-K. It has the dual heat riser tubes which transfer the heat from the exhaust and to the intake manifold to prevent carborator freezing.Use two manifold gaskets # VWC-113-129-717-A and two manifold boots # VWC-113-129-729-B. Use these parts to convert from fuel injection to carborarators on 1975-79 Beetles.

These are Genuine VW end castings that connect the Center intake manifold section # VWC-113-129-701M to the cylinder head. This intake manifold fits all 1600cc dual port Type 1 style engines. The carborator that fits this manifold is the 34 PICT-3, part #C24-113-129-031-K. It has the dual heat riser tubes which transfer the heat from the exhaust and to the intake manifold to prevent carborator freezing.Use two manifold gaskets # VWC-113-129-717-A and two manifold boots # VWC-113-129-729-B. Use these parts to convert from fuel injection to carborarators on 1975-79 Beetles.

These are Genuine VW end casting for the Right side that connect the Center intake manifold section # VWC-113-129-701M to the cylinder head. This intake manifold fits all 1600cc dual port Type 1 style engines. The carborator that fits this manifold is the 34 PICT-3, part #C24-113-129-031-K. It has the dual heat riser tubes which transfer the heat from the exhaust and to the intake manifold to prevent carborator freezing.Use two manifold gaskets # VWC-113-129-717-A and two manifold boots # VWC-113-129-729-B. Use these parts to convert from fuel injection to carborarators on 1975-79 Beetles.